Interlogix NX-8 User Manual download pdf (Page 58)

NX-8 Control

REGULATORY NOTICES

LOCAL TELEPHONE COMPANY INTERFACE

INFORMATION

Telephone Connection Requirements

Except for telephone company provided ringers, all connections

to the telephone network shall be made through standard plugs

and standard telephone company provided jacks or equivalent in

such a manner as to allow for immediate disconnection of the

terminal equipment. Standard jacks shall be so arranged that if

the plug connected thereto is withdrawn, no interference to the

operation of the equipment at the customer’s premises which

remains connected to the telephone network, shall occur by

reason of such withdrawal.

Incidence Of Harm

Should terminal equipment or protective circuitry cause harm to

the telephone network, the telephone company shall, where

practical, notify the customer that temporary discontinuance of

service may be required. However, where prior notice is not

practical, the telephone company may temporarily discontinue

service if such action is deemed reasonable in the circumstances.

In the case of such temporary discontinuance, the telephone

company shall promptly notify the customer who will be given the

opportunity to correct the situation. The customer also has the

right to bring a complaint to the FCC if he feels the disconnection

is not warranted.

Changes In Telephone Company Equipment Or

Facilities

The telephone company may make changes in its

communications facilities, equipment, operations, or procedures

where such action is reasonably required and proper in its

business. Should any such change render the customers terminal

equipment incompatible with the telephone company facilities, the

customer shall be given adequate notice to make modifications to

maintain uninterrupted service.

General

The FCC prohibits customer provided terminal equipment be

connected to party lines.

Importance Of The Ringer Equivalence Number

The Ringer Equivalence Number (REN) of this device is 0.1B.

This number is a representation of the electrical load that it

applies to your telephone line.

Malfunction Of The Equipment

In the event that the device should fail to operate properly, the

customer shall disconnect the equipment from the telephone line

to determine if it is the customers equipment that is not

functioning properly. If the problem is with the device, the

customer shall discontinue use until it is repaired.

Equipment Information

Manufacturer Of Connecting Equipment:

CADDX CONTROLS, INC.

FCC Registration Number:

GCQUSA-31771-AL-T, RINGER EQUIVALENCE: 0.1 B

(Applies to products which have the CE mark attached)

CE DECLARATION OF CONFORMITY

Manufacturer’s Name: Caddx Controls

Manufacturer’s Address: 1420 North Main Street

Gladewater TX 75647

EU Representative: UTC Fire & Security Europe

Product Identification

Product: NetworX

Model: NX-8

Brand: CADDX

R&TTE Directive

See EMC and LVD tests below

EMC Directives:

EN50

081-1 EN50130-4

EN55022 EN60950

EN61000-3-2 EN61000-3-3

LVD Directive:

EN 609

50: 1999-4 3rd edition

Means of Conformity

We declare under our sole responsibility that this product is in

conformity with Directive 1999/5/EC (R&TTE); Directive

73/23/EEC (LVD); and Directive 89/336/EEC (EMC) and based

on test results using (non)-harmonized standards in accordance

with the Directives mentioned.

Additional Tests

This equipment has been tested and found to comply with the

following standards (which are no longer required for

compliance).

Network Compatibility Declaration

e declare under our sole responsibility that this product is

designed to work with the networks in the countries marked with

a check () and may have interworking problems with the

countries that are not checked. Due to the inherent differences in

the individual PSTNs, certain software settings may need to be

adjusted on a country-to-country basis. If it is desired to use this

equipment on a network other than the one on which it was

originally installed, you should contact your equipment supplier.

() Austria (_) Liechtenstein

() Belgium () Luxembourg

() Denmark () Netherlands

() Finland () Norway

() France () Poland

() Germany () Portugal

() Greece () Spain

() Iceland () Sweden

() Ireland () Switzerland

() Italy () United Kingdom

Telecom Approval Notice

This equipment has been approved in accordance with the

Council Decision 98/482/EC for pan-European, single terminal

connection to the public switched telephone network (PSTN).

However, due to the differences between the individual PSTNs

provided in different countries, the approval does not, of itself,

give an unconditional assurance of successful operation on every

PSTN network termination point. In the event of problems, you

should contact your equipment supplier in the first instance.

Electrical Requirements

his device automatically adjusts to voltages within the range of

230 V 50/60 Hz. Fuse: Type T 200mA 250 VAC

1 2 ... 53 54 55 56 57 58 59 60 61

Comments to this Manuals

No comments

Interlogix NX-8 User Manual Page 58

Comments to this Manuals

Related products and manuals for Control panel Interlogix NX-8