Interlogix NX-8 User Manual download pdf (Page 35)

NX-8 Control

LOCATION 109 - PARTITION 8 ENTRY EXIT TIMERS (4 segments, numerical data)

cation 109 is used to enter in seconds the Entry and Exit times. There are 2 separate entry and exit times. Valid

entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition 1 will be used.

Segment 1, Entry Time 1: Entry time that will be used when a Delay 1 zone type initiates an entry delay.

Segment 2, Exit Time 1: Exit time that will be used for all zones designated as Delay 1.

Segment 3, Entry Time 2: Entry time that will be used when a Delay 2 zone type initiates an entry Delay.

Segment 4, Exit Time 2: Exit time that will be used for all zones designated as Delay 2.

LOCATIONS 110-149 ARE USED TO CHANGE THE ZONE TYPES (Configurations) AS LISTED IN THE TABLE

ON PAGE 20. THESE LOCATIONS ARE CONSIDERED ADVANCED PROGRAMMING AND SHOULD

ONLY BE CHANGED WITH A THOROUGH UNDERSTANDING OF THE OPERATION OF EACH BIT.

LOCATION 110 - ZONE TYPE 1 ALARM EV

ENT CODE (1 segment, numerical data)

Location 110 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen

from the list on page 54. The zone ID will be that zone that is in alarm. If 4+2 format is

being used, the number

programmed in this location will be sent as the tens digit. When using 4+2 the digit in location 110 should be from 1-

15.The zone ID for 4+2 formats will be the ones digit of the zone that is in alarm.

LOCATION 111 - ZONE TYPE 1 CHARACTERIS

TIC SELECT (3 segments, feature selection data)

Segment 1: 1 = Fire (turn on if this is a fire zone).

2 = 24 hour (turn on for non-fire 24 hour zones).

3 = Keyswitch zone. (normally open switch)

4 = Follower (turn on for burglary zones that are Instant during non-entry times).

5 = Delay 1 zone (follows timer 1 entry and exit times).

6 = Delay 2 zone (follows timer 2 entry and exit times).

7 = Interior (turn on if this zone should Automatically Bypass or Bypass for Stay Arming).

8 = Local only (turn on if this zone should not be reported).

Segment 2: 1 = On if Zone Type will beep the keypad for alarm.

2 = On if Zone Type will sound the yelping siren for alarm.

3 = On if Zone Type will sound the temporal siren for alarm.

4 = On if Zone Type will chime.

5 = On if Zone Type can be bypassed.

6 = On if Zone Type is included in the group shunt.

7 = On if Zone Type is force armable.

8 = On if Zone Type is entry guard.

Segment 3: 1 = On enables Fast Loop Response. (50mS)- Off= 500mS

2 = On enables Double End Of Line Tamper zone. (Mainly used for tamper on wireless zones)

3 = On enables Trouble Reporting zone. (Day zone and Fire zones)

4 = On if Zone Type is a Cross Zone.

5 = On enables Dialer Delay zone. (See location 40, page

24)

6 = On if

Zone Type will swinger shutdown. (See location 38, page 23)

= On enables Restore reporting.

8 = On enables Listen-In. (See location 40, page 24)

LOCATION 112 - ZONE TYPE 2 ALARM EV

ENT CODE (1 segment, numerical data)

Location 112 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen

from the list on page 54. The zone ID will be that zone that is in alarm. If 4+

2 format is being used, the number

programmed in this location will be sent as the tens digit. When using 4+2 the digit in location 112 should be from 1-

15. The zone ID for 4+2 formats will be the ones digit of the zone that is in alarm.

LOCATION 113 - ZONE TYPE 2 CHARACTERIS

TIC SELECT (3 segments, feature selection data)

Use "Zone Type Characteristic Selections" described in Location 111, page 35.

LOCATION 114 - ZONE TYPE 3 ALARM EVENT

CODE (1 segment, numerical data)

Location 114 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen

from the list on page 54. The zone ID will be that zone that is in alarm. If 4+2 format is

being used, the number

programmed in this location will be sent as the tens digit. When using 4+2, the digit in location 114 should be from 1-

15. The zone ID for 4+2 formats will be the ones digit of the zone that is in alarm.

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 60 61

Comments to this Manuals

No comments

Interlogix NX-8 User Manual Page 35

Comments to this Manuals

Related products and manuals for Control panel Interlogix NX-8