Interlogix NX-4 User Manual download pdf (Page 16)

NX-4 Control

Page 14

LOCATION 6 - PROGRAMMING PHONE #2 (20 segments, numerical data)

Phone #2 is programmed in location 6. A "14" indicates the end of the phone number. Delays of four seconds can be

programmed at any point in the phone number by programming a "13" in the appropriate segment. If tone dialing is

desired, program a "15" in the segment where tone dialing should begin. If the entire number should be tone dialing,

program a "15" in the first segment. Program an A11" for a Ar@, and a A12" for a A#@. Caution: A call-waiting cancel

on a non- call waiting line will prevent successful connection to the central station.

LOCATION 7 - ACCOUNT CODE FOR THE PHONE #2 (6 segments of numerical data)

The account code sent when Phone #2 is dialed is programmed in location 7. Program a A10" in the segment

immediately after the last digit of the account code. If the account code is 6 digits long, program all 6 segments. If

this location is left unprogrammed, account code 1 will be used when the second phone number is dialed.

LOCATION 8 - COMMUNICATOR FORMAT FOR PHONE # 2 (1 segment, numerical data)

Location 8 contains the communicator format used to transmit to the receiver connected to Phone #2. Consult the

instruction manual for your central station receiver to determine which format is compatible, and select from the 15

formats listed on page 13. If you require a format other than those listed, review the override options described in

Location 18 to build the appropriate format. A "15" must be programmed in location 8 in addition to the entries in

location 18 in order to create a special format. If this location contains a "0", format 1 will be used when Phone #2 is

dialed.

LOCATION 9 - DIAL ATTEMPTS/BACKUP CONTROL FOR PHONE #2 (2 segments, numerical data)

Segment 1, Dial attempts: Segment 1 of Location 9 is used to enter the number of dial attempts (1 to 15 attempts)

the communicator will make to Phone #2 before ending the notification process. Factory default is "8" and the

communicator will make the same number of attempts as those programmed in location 3.

Segment 2, Phone #2 Backup Control: Programming a "0" in Segment 2 of this location will cause the NX-4 to

make the designated number of attempts to Phone #1 before setting the "Fail To Communicate" condition and stop

reporting. Programming a "1" in this segment will cause the NX-4 to stop trying to communicate after the designated

number of attempts have been made to Phone #2. If a "2" is programmed in this segment, it will cause the NX-4 to

make the dial attempts in increments of two. The first two attempts will be made to Phone #2, the next two attempts

to Phone #1, then repeating until the total number of attempts designated in Segment 1 is completed.

REPORTING EVENTS TO PHONE NUMBER 2

Phone #2 can be used to back up Phone #1 or for a second receiver to multi-report or split report events. Location 10

is used to select which events are reported to Phone #2. If dual or split reporting is not desired, location 10 should be

left at the factory default of "0". If multi-reporting or split reporting is desired, location 10 should be used to select

only those events that should be reported to Phone #2. If no events should be reported to Phone #2, location 10

should be "0".

LOCATION 10 - EVENTS REPORTED TO PHONE #2 (2 segments of feature selection data)

Segment 1: 1 = Alarms and Alarm Restores.

2 = Opening and Closings.

3 = Zone Bypass and Bypass Restores.

4 = Zone Trouble and Trouble Restores.

5 = Power Fail, Low Battery, Power Restore, and Low Battery Restore.

6 = Bell Cut, Bell Cut Restore.

7 = Test Reports.

8 = Start and End programming, Download complete.

Segment 2: 1 = Zone and Box Tamper and Tamper Restore.

2 = Auxiliary Power Over-current and Restore.

3 = Sensor Missing and Restore.

4 = Sensor Low Battery and Restore.

5 = Expander Trouble and Restore.

6 = Fail To Communicate.

7 = Reserved.

8 = Reserved.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 43 44

Comments to this Manuals

No comments

Interlogix NX-4 User Manual Page 16

Comments to this Manuals

Related products and manuals for Control panel Interlogix NX-4