Interlogix NX-148E-RF User Manual download pdf (Page 9)

NX-148E-RF LCD Touchpad w ith Receiver Installation Instructions 9

Silent exit (EXIT)

To silence the exit beeps during exit delay (while the system is

disarmed), do the following:

1. Enter * EXIT.

2. Enter your user code.

3. To exit, press #.

Reference tables

Table 9. Service menu messages

Message

Explanation

Control over current

A short circuit of a pow er supply has

occurred.

Control siren trouble

Open circuit on the bell or siren circuit.

Control box tamper

(Optional) The box tamper circuit has

activated.

Control phone trouble

The phone line connected to the control is

not operating properly.

Control fail to comm.

The control made an unsuccessful attempt

to communicate a message to the central

station.

Control ground fault

A short to ground has been detected on a

control circuit.

Control loss of time

Your system has lost total pow er and needs

the clock reset.

Control pow er trouble

The main pow er to the system is off.

Control low battery

The standby battery is low .

Expansion aux comm

fail

A auxiliary reporting device (i.e. NX-580E,

NX-582E, etc.) has failed to communicate.

Expansion over

current

A short circuit of an expansion devices

pow er supply has occurred.

Expansion pow er

trouble

The main pow er to an expansion pow er

supply is off.

Expansion low battery

An expansion pow er supply has a low

battery.

Expansion box tamper

A box containing an expansion device has

been opened.

Expansion RF jammed

A radio receiver is being jammed.

Expansion trouble

An expansion device or touchpad is not

reporting to the control panel.

Expansion siren

trouble

An expansion device has detected trouble

on the bell or siren circuit.

Zone tamper, press *

A zone is tampered. Press * to identify the

tampered zone.

Zone low battery,

press *

A w ireless device has a low battery. Press *

to identify the zone.

Zone lost, press *

A w ireless or multiplexed zone device is not

reporting to the control. Press * to identify

the zone.

Zone trouble, press *

A zone is experiencing trouble. Press * to

identify the zone.

Table 10. Log messages

Display

Description

TXlobat

Transmitter low battery

ZN Lost

Zone lost - A w ireless multiplexed zone

device is not reporting to the control.

Duress

The control has been armed or disarmed

w ith a Duress code.

Man Fire

Manual fire - Touchpad Fire has been

activated.

Aux 2

Auxiliary 2 - Touchpad Medical has been

activated.

Panic

Touchpad Panic has been activated.

KP Tamper

Touchpad Tamper - The touchpad tamper

has been activated.

BoxTamp

Box Tamper - The box tamper circuit has

been activated.

AC Fail

AC failure has been detected.

OverCur

Over current - A short circuit of a pow er

supply has occurred.

Srn Tamp

Siren tamper - A siren or speaker tamper

has been detected.

Tel Flt

Telephone fault - A telephone fault or

tamper has been detected.

Exp Trb

Expansion trouble - An expansion device or

touchpad is not reporting to the control.

Log Full

The event log is full.

Open

Reports, user number, date, time and

partition of opening.

Reports, user number, date, time and

partition of closing.

Exit Err

Exit error - Entry/exit zone w as faulted when

the exit delay expired.

Rec Close

Recent close - An alarm occurred within 5

minutes of the control being armed.

Autotest

Automatic test - Sending a communicator

test at a specified interval.

Start Prog

Start programming - Local Programming

has started.

End Prog

End programming -Local programming has

ended.

Start Dnld

Start dow nload - Dow nload session has

started.

End Dnld

End dow nload - Dow nload session has

ended.

Cancel

Cancel w as initiated w ithin 5 minutes of an

alarm.

Gnd Flt

Ground fault - A short to ground has been

detected.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Comments to this Manuals

No comments

Interlogix NX-148E-RF User Manual Page 9

Comments to this Manuals

Related products and manuals for Safety Interlogix NX-148E-RF