Interlogix TX-6310-01-1 User Manual download pdf

TX-6310-01-1 Carbon Monoxide Alarm Manual

Figure 1: Alarm features

Test/Hush button

Alarm sounder

Green Power LED

Red Alarm LED

Attention: Please take a few minutes to thoroughly read this

guide which should be saved for future reference and passed

on to any subsequent owner.

The TX-6310-01-1 CO alarm is only compatible with Simon XT

panels with firmware v1.4 or higher. Refer to the panel

installation instructions for revision verification details. It is

currently not compatible with other control panels. Please

contact Technical Support for any questions regarding

compatibility.

Description

The TX-6310-01-1 wireless carbon monoxide (CO) alarm

monitors the levels of CO gas and gives early warning when

potentially dangerous levels exist. It does not detect fire,

smoke, or any other gas. If a dangerous concentration of CO is

detected by patented and field-proven electrochemical sensor,

an LED indicator illuminates and an internal siren is activated

in temporal 4 pattern. The CO alarm also transmits an alarm

signal to the control panel within 15 seconds of detecting

dangerous concentration of CO gas. The control panel

activates its internal siren and reports the alarm condition to

the central monitoring station (if the system is monitored). The

CO alarm also detects low battery, wall tamper, and sensor

end-of-life. These trouble codes are transmitted to the control

panel. The alarm automatically resets when CO is no longer

detected.

The TX-6310-01-1 wireless CO alarm is Listed and compliant

with the ANSI/UL 2034 standard for CO alarms. It is intended

for residential indoor dwelling unit applications and other areas

approved by the authority having jurisdiction (AHJ). It is not

intended for use in industrial applications.

WARNING: After seven years from initial power up, this alarm

will beep two times every 30 seconds to indicate that it is time

to replace the alarm. Replace the alarm immediately! It will not

detect CO in this condition.

To help identify the date to replace the alarm, an area has

been reserved on the side of the alarm. Write the “replace by”

date (seven years from power up) with a permanent marker in

the area provided.

Alarm location

CO alarms should be mounted in or near bedrooms and living

areas. We recommend that you install an alarm on each level

of your home.

When choosing your installation locations, make sure you can

hear the alarm from all sleeping areas. If you install only one

CO alarm in your home, install it near bedrooms, not in the

basement or furnace room.

Place the alarm out of reach of children. Under no

circumstances should children be allowed to handle the CO

alarm.

Figure 2: Recommended locations

Dining

Kitchen

Bedroom

Living room

Locations to avoid

Improper location can affect the sensitive electronic

components in this alarm. To avoid causing damage to the

unit, to provide optimum performance, and to prevent

unnecessary nuisance alarms:

• Do not install in kitchens, garages, or furnace rooms that

may expose the sensor to substances that could damage

or contaminate it.

• Do not install in areas where the temperature is colder

than 40°F (4.4°C) or hotter than 100°F (37.8°C) such as

crawl spaces, attics, porches, and garages.

• Do not install within 5 ft. of heating or cooking appliances.

(We recommend 15 ft. to prevent nuisance alarms.)

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - Alarm location

TX-6310-01-1 Carbon Monoxide Alarm Manual Figure 1: Alarm features Test/Hush buttonAlarm sounderGreen Power LEDRed Alarm LED Attention: Please take a

Page 2 - Mounting the alarm

• Do not install near vents, flues, chimneys, or any forced/unforced air ventilation openings. • Do not install on metal surfaces. • Avoid mounting

Page 3 - Testing

Figure 6: Horizontal mounting MountingholeMounting holeMounting latchAlarm procedure labelWar n i n gXXXXxxXXX x xxxXX XXX XXXXxxxXXXX XXX XXXx

Page 4 - Regulatory information

Tamper condition does not restore: A canned CO testing agent must be used for the CO functional gas test. • Make sure the CO alarm body is properly i

Page 5 - Operation characteristics

Operation characteristics Table 1: Operation characteristics LED Display Alarm sound Unit status Control panel status Recommendation Normal oper

Page 6

Information about carbon monoxide Carbon monoxide is a colorless, odorless, and tasteless poison gas that can be fatal when inhaled. CO inhibits the

Page 7 - Manufacturing information

Important warning statements This carbon monoxide alarm is designed to detect carbon monoxide from ANY source of combustion. It is NOT designed to de

Page 8 - Alarm procedure

Alarm procedure 2533-7201-00 8 / 8 P/N 466-2393 • REV A • ISS 14FEB11

Comments to this Manuals

No comments

Interlogix TX-6310-01-1 User Manual

Browse online or download User Manual for Sensors Interlogix TX-6310-01-1. Interlogix TX-6310-01-1 User Manual

Summary of Contents

Comments to this Manuals