NetworX™ Series NX-148E LCD Keypad User Manual
NX-148E LCD Keypad 8CANCEL / ABORT FEATURE (Optional, if programmed) The cancel light will flash during an abort delay time. If a code is entered fo
NX-148E LCD Keypad 9If you do not know the number of the zone you wish to bypass, use the following steps: Step 1 Press r • The descripti
NX-148E LCD Keypad 10 Select an Option Press for Help Auxiliary Key - If programmed, you can activate the auxiliary alarm by pressing the Emergency
NX-148E LCD Keypad 11 VIEW ZONE STATUS Step 1 Press r • . The LCD Screen will display the zone status. Step 2 Use the up and down scroll keys
NX-148E LCD Keypad 12 DISPLAY TEST FUNCTION This function will perform a test of the LCD display. No alarms or reports will be sent. Step 1 Press
NX-148E LCD Keypad 13 CHANGING USER CODES Step 1 Press r 5 . The LCD Screen will prompt for a code. Step 2 Enter [master code]. The LCD S
NX-148E LCD Keypad 14 PROMPT Outputs used? DO NOT CHANGE THIS SEGMENT! Open / Close Rprt? Bypass enable? Arm / Disarm? (These are for use b
NX-148E LCD Keypad 15 READING THE EVENT LOG The control panel has an event log that can be retrieved using a master code. This log contains a listin
NX-148E LCD Keypad 16 SETTING THE SYSTEM CLOCK Step 1 Enter r 9 7 . The LCD Screen will prompt for a code. Step 2 Enter [master c
NX-148E LCD Keypad 17 IV. PARTITIONED SYSTEMS OPERATION This system is “ is not “ partitioned. If your system is multi-partitioned and th
NX-148E LCD Keypad 18 This display is reflecting all 8 areas are Ready, and Area 5 is disarmed. NOTE: If a number is flashing on the Armed line, tha
NX-148E LCD Keypad 19 OPERATING INDIVIDUAL AREAS IN THE MULTI-PARTITION MODE Enter a code that is a valid arm/disarm code for the area you wish to
NX-148E LCD Keypad 20 V. KEYPAD CONTROL TONES (BEEPS) A sounder is built into the keypad and may sound for any of the following reasons: Beeps
NX-148E LCD Keypad 21 VI. SERVICE DISPLAY The following message will be displayed periodically if the security system requires service. Call your s
NX-148E LCD Keypad 22 Expansion Aux. comm. fail An auxiliary reporting device has failed to communicate. Expansion Box tamper A box containing an expa
NX-148E LCD Keypad 23 VII. APPENDIX A - EVENT LOG NOTE: Your system may not have all of the features listed in this table. DISPLAY DESCRIPTION TX
NX-148E LCD Keypad 24 DISPLAY DESCRIPTION Cancel Cancel System is disarmed and the Cancel button was pressed within 5 minutes of an alarm. Gnd Flt
NX-148E LCD Keypad 25 VIII. EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition. For
NX-148E LCD KEYPAD FIRE light is “on” to indicate fire alarm, flashes to indicate a trouble condition with your fire system. READY light is “on” w
SYSTEM NOTES
NX-148E LCD Keypad 1TABLE OF CONTENTS I. GLOSSARY OF TERMS...
NX-148E USERS MANUAL NX148EUC05 REV C (June2005)
NX-148E LCD Keypad 2THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION. ALL USERS OF YOUR SE
NX-148E LCD Keypad 3I. GLOSSARY OF TERMS Abort Delay: An option that allows a delay in reporting to the central station. Authority Level: The lev
NX-148E LCD Keypad 4II. UNDERSTANDING THE LIGHTS Armed Light The armed light is “on” when the system is armed. The armed light is “off” when it is
NX-148E LCD Keypad 5III. KEYPAD FUNCTIONS ARMING YOUR SYSTEM IN THE “AWAY” MODE AWAY is utilized when the user is going away from the premise and w
NX-148E LCD Keypad 6ARMING YOUR SYSTEM IN THE “STAY” MODE STAY is utilized when the user is inside the premise and wants protection around the perimet
NX-148E LCD Keypad 7USING THE QUICK ARM The Quick Arm feature may be used if it is enabled. Quick Arm will allow the user to arm the security system
Comments to this Manuals